我们在驾驶搅拌一体机的过程中会遇到机油报警灯亮的情况，那么我们该怎么呢？下面来看一下常见的故障原因及措施。

In the process of driving the mixing machine, we will encounter the situation that the oil alarm light is on. How can we solve this problem? Let's take a look at the common fault causes and solutions.

搅拌一体机机油报警灯亮的故障分析及方法

Failure Analysis and Solution of the Engine Oil Warning Light on the Agitator

1. 机油量不足的办法，每天都应检查油底壳中的油位，保证油位的正常，如果发现不足，一定要添加同一厂家生产的同一型号的机油。

1. First of all, the solution to the problem of insufficient oil is to check the oil level in the oil pan every day to ensure that the oil level is normal. If insufficient oil is found, it is necessary to add oil of the same model produced by the same manufacturer.

2. 机油泵磨损，机油泵泵轴与衬套之间的间隙、齿轮端面与泵盖的间隙、齿侧间隙或径向间隙因磨损而过大时，都会导致油量减小，使机油压力下降。此时应更换磨损的零件研磨泵盖内平面，使之与齿轮端面的间隙恢复到标准范围。

2. When the oil pump is worn, and the clearance between the oil pump shaft and the bushing, the clearance between the gear end face and the pump cover, the clearance between the gear side or the radial clearance is too large due to wear, the oil volume will be reduced and the oil pressure will be reduced. At this time, the worn parts should be replaced and the inner surface of the pump cover should be ground to restore the clearance between the worn parts and the gear end face to the standard range.

3. 机油泵不转，办法：更换损坏的平键或集滤器。

3. The oil pump does not rotate. The solution: replace the damaged flat key or filter collector.

4. 发动机油温过高，如果发动机冷却系统水垢过多、散热不良、长时间超负荷作业或者喷油泵的供油时间过迟等都会使发动机过热，加速机油的老化、变质、变稀，从各配合间隙中泄漏，压力降低。此时应及时水垢、调整供油时间、让发动机在额定负荷内工作。

4. The engine oil temperature is too high. If the engine cooling system has too much scale, poor heat dissipation, long-time overload operation, or the fuel supply time of the fuel injection pump is too late, the engine will overheat, accelerate the aging, deterioration, thinning of the engine oil, leak from various fitting gaps, and the pressure will drop. At this time, the scale shall be removed in time, the oil supply time shall be adjusted, and the engine shall work within the rated load.

5. 主轴承与连杆轴承的配合间隙增大，发动机长期使用后主曲轴与连杆轴承的配合间隙逐渐增大，泄漏增加，机油压力便下降，此时可以修磨曲轴，选配新的连杆轴承与主轴承，恢复其配合间隙即可。

5. The fit clearance between the main bearing and the connecting rod bearing increases. After the engine has been used for a long time, the fit clearance between the main crankshaft and the connecting rod bearing gradually increases. With the increase of leakage, the oil pressure decreases. At this time, the crankshaft can be ground, new connecting rod bearing and main bearing can be selected, and the fit clearance can be restored.

6. 机油散热器漏油，外漏会污染发动机表面，压力下降；内漏使机油进入水箱，冷却系统的散热效果变差，发动机过热，机油变稀，压力下降，拆下散热器，修理或更换，恢复其功能。

6. The oil radiator leaks oil, which will pollute the engine surface and reduce the pressure; The internal leakage makes the engine oil enter the water tank, the cooling effect of the cooling system becomes worse, the engine overheats, the engine oil becomes thinner, and the pressure drops. Remove the radiator, repair or replace it, and restore its function.

7. 压力传感器失灵或主油道压力传感器的油道堵塞而油流不畅时，机油压力就会下降，可做如下检查：发动机怠速运转，松开油管接头，观察油流情况，判断故障部位，更换压力传感器或清洗油道。

7. When the pressure sensor fails or the oil passage from the main oil passage to the pressure sensor is blocked and the oil flow is not smooth, the oil pressure will drop. The following inspections can be made: the engine runs at idle speed, loosen the oil pipe connector, observe the oil flow, determine the fault location, replace the pressure sensor or clean the oil passage.

搅拌一体机机油报警灯亮的异常分析就讲解到这里了，我们从七个方面了解起来，更多相关事项就来我们网站http://www.zkhntjbj.com咨询！

This is the end of the abnormal analysis of the oil alarm light of the agitator. We have learned about it from seven aspects, and more relevant matters will come to our website http://www.zkhntjbj.com consulting service