The brake system of the automatic charging mixer is very important to the concrete mixer. Therefore, it is necessary for us to master some knowledge of vehicle braking and four braking methods of automatic charging mixer.

1.点刹，是很多司机都知道的制动方法，一般在自动上料搅拌机遇到紧急情况时，猛踩刹车是非常不理智的行为，很容易发生危险的，此时应该先轻点刹车，再放开，再轻点，再放开，让车速逐渐降低，这种方法通常在雨天或冰雪路面上使用，可以防止车辆跑偏或侧滑。

1. Brake tapping is a braking method that many drivers know. Generally, when the automatic charging mixer encounters an emergency, it is very irrational to step on the brake, which is very easy to cause danger. At this time, the brake should be gently applied, then released, and then released, so that the speed gradually decreases. This method is usually used in rainy days or ice and snow roads, which can prevent the vehicle from running sideways or Sideslip.

2.紧急制动，当自动上料搅拌机在行驶的过程中遇到紧急情况是，驾驶员应迅速放松油门踏板，用力踩下刹车，同时拉紧手刹，尽可能在短距离内将车辆停住，以达到避免事故的目的，这种方法是不得已的情况下采取的紧急措施，因为它对车辆的轮胎和各个部件是有损害的，同时制动时的方向已经不能控制，所以应该尽量避免这种制动。

2. Emergency braking: when the automatic charging mixer encounters an emergency in the process of driving, the driver should quickly release the accelerator pedal, step on the brake forcefully, and at the same time, tighten the hand brake, and stop the vehicle in a short distance as far as possible, so as to avoid accidents. This method is an emergency measure to be taken under the circumstances of necessity, because it can affect the tires and various parts of the vehicle If there is damage, the direction of braking can not be controlled at the same time, so this kind of braking should be avoided as far as possible.
              

3.先急后松，这种方法就是在遇到紧急情况时，先急踩刹车接着要缓冲一下再踩刹车，然后根据发生情况点的距离慢慢松开制动踏板，再更换与速度匹配的档位，正常行驶即可。这种方法可以大大降低由车速急剧变化带来的冲击，使车辆运行稳定。

3. Emergency first and then release. This method is that in case of emergency, step on the brake first, then cushion it, then step on the brake, then slowly release the brake pedal according to the distance of the occurrence point, and then change the gear matching with the speed to drive normally. This method can greatly reduce the impact caused by the rapid change of vehicle speed and make the vehicle run stably.

4.预见性制动，这种方法主要就是在司机开车过程中，对道路上的车辆、行人、非机动车的变化，做预见性的制动，具体做法就是将脚放开油门踏板，利用发动机怠速时的牵阻力作用来降低车速，然后根据具体情况继续减速或者轻踏油门，让车辆平稳的减速或者停车，这种方法能有效保证行车安全，降低车辆零部件的损害程度，这种制动方法在平时使用的多，也较普遍。

4. Predictive braking. This method is mainly to make predictive braking on the changes of vehicles, pedestrians and non motor vehicles on the road during the driving process. The specific method is to release the accelerator pedal, use the traction resistance of the engine at idle speed to reduce the speed, and then continue to slow down or gently step on the accelerator according to the specific situation, so that the vehicle can slow down or stop smoothly This method can effectively ensure the driving safety and reduce the damage degree of vehicle parts. This braking method is widely used in peacetime.

自动上料搅拌机由于车身比较重，在平时的行车过程中对车辆的制动更应该要注意，多知道一些车辆的制动方法，在行车的路上就多了一份安全保障！

Due to the heavy body of the automatic charging mixer, more attention should be paid to the braking of the vehicle in the normal driving process. If you know more about the braking methods of some vehicles, you will have a more safety guarantee on the road!

以上就是自动上料搅拌机的四种制动方法的介绍，希望对大家有所帮助，如您想要了解更多搅拌机资讯欢迎点击网站：www.zkhntjbj.com。

The above is the introduction of the four braking methods of the automatic charging mixer, hoping to help you. If you want to know more about the mixer, please click the website: www.zkhntjbj.com 。