The mixing shaft end of automatic feeding mixer series is a combined seal type, which is composed of multi-layer seals such as rubber seals and steel seals. The quality of sealing affects the overall performance of the whole mixing station. Therefore, it is very important to choose a good seal. The root cause of mixer shaft end leakage is the damage of floating seal. Due to the damage of seal and oil seal, the lubrication system is short of oil, which leads to the wear of sliding hub and rotating hub.

由于轴端泄漏和与搅拌轴摩擦引起的轴承磨损，轴端温度过高。 主轴端是一个集中部分，在高强度应力作用下，零件的使用寿命将大大减少。 因此，轴端密封，油封，滑动轮毂和旋转轮毂中的密封及时更换; 建议将主轴端部的泄漏端侧的轴承作为原始密封配件，以避免尺寸差异，磨损和损坏大轴及时检查润滑系统：

The temperature of the shaft end is too high due to the leakage of the shaft end and the bearing wear caused by the friction with the stirring shaft. The spindle end is a concentrated part. Under the action of high strength stress, the service life of parts will be greatly reduced. Therefore, the shaft end seal, oil seal, seal in sliding hub and rotating hub should be replaced in time; it is suggested that the bearing on the leakage side of the spindle end should be used as the original sealing parts to avoid dimensional difference, wear and damage to the main shaft, and the lubrication system should be checked in time

1.润滑系统主油泵旋转轴磨损现象

1. The main oil pump rotating shaft of the lubrication system is worn

2.润滑系统主油泵压力表接口柱塞不能正常工作

2. The plunger at the pressure gauge interface of the main oil pump of the lubrication system cannot work normally

3.渐进式油分配器安全阀阀芯在润滑系统中堵塞，无法分配。

3. The valve core of progressive oil distributor safety valve is blocked in the lubrication system and cannot be distributed.

由于上述原因，轴端润滑系统出现故障，需要更换润滑系统的主油泵。

As a result of the above reasons, the shaft end lubrication system fails and the main oil pump of the lubrication system needs to be replaced.
          

如果你想做一个自动上料搅拌机，你应该从以下几个方面入手：

If you want to make an automatic feeding mixer, you should start from the following aspects:

1）整个自动上料搅拌机的成本控制。 这主要是指自动上料搅拌机，因为自动上料搅拌机的投入和生产成本相对较低且易于管理。

1) Cost control of the whole automatic feeding mixer. This mainly refers to the automatic feeding mixer, because the input and production costs of the automatic feeding mixer are relatively low and easy to manage.

2）细分整个搅拌机的生产过程，掌握每个细分生产过程的成本。

2) Subdivide the whole mixer production process, master the cost of each production process.

3）做好整个搅拌机的销售计划，制定相应的生产和销售计划。

3) Do a good job in the whole mixer sales plan, formulate the corresponding production and sales plan.

4）做好全站金融审计制度，确保整个资金链的有序发展。 建议是减少销售，而不是缺乏资金链。

4) Do a good job in the whole station financial audit system to ensure the orderly development of the whole capital chain. The suggestion is to reduce sales, not lack of capital chain.

以上是自动上料搅拌机混合器轴端泄漏的原因介绍，相信大家都有所了解了，如想了解更多精彩资讯请点击我们的网站：http://www.zkhntjbj.com

The above is the reason for the leakage of the shaft end of the automatic feeding mixer. I believe you all know about it. For more wonderful information, please click our website: http://www.zkhntjbj.com