我们作为一家自动上料搅拌机行业中的生产厂家，让每个工作人员掌握维修技巧是非常重要的管理手段，今天我们针对漏油情况的发生，来讲讲对自动上料搅拌机本身所带来的危害究竟有多大！并针对问题的出现给出相应的技巧。

As a professional manufacturer in the automatic feeding mixer industry, it is a very important management means to let each staff master the maintenance skills. Today, we are aiming at the occurrence of oil leakage to talk about the harm to the automatic feeding mixer itself! And for the emergence of the problem gives the corresponding solution skills.

在冬季起车时，若因预热不足，油温度就会出现过低。当油液、油封未达到工作温度时，自动上料搅拌机在整个起车过程中，就需停罐怠速运转10min20min，待油温达到正常状态后，再开始进行转罐工作。

When starting in winter, the oil temperature will be too low due to insufficient preheating. When the oil and oil seal do not reach the working temperature, the automatic feeding mixer needs to stop the tank and idle for 10min to 20min during the whole starting process. After the oil temperature reaches the normal state, the tank can be rotated.

若使用时间过长，油封在达到正常磨损的情况下，就需对油封进行更换。

If the service time is too long, the oil seal needs to be replaced under the condition of normal wear.

液压油缸时间未得到有效更换，或滤芯质量不合格，液压油过脏，会加快油封磨损速度。尽快对自动上料搅拌机的液压油及滤芯进行更换。

If the time of hydraulic cylinder is not effectively replaced, or the quality of filter element is unqualified, and the hydraulic oil is too dirty, the wear speed of oil seal will be accelerated. Replace the hydraulic oil and filter element of the automatic feeding mixer as soon as possible.
           

液压油出现变质、乳化，润滑性能下降，加快油封磨损速度，尽快更换液压油、滤芯，严重时，还应对自动上料搅拌机的相关系统进行清洗。

The hydraulic oil deteriorates and emulsifies, the lubrication performance decreases, the oil seal wear speed is accelerated, and the hydraulic oil and filter element are replaced as soon as possible. When it is serious, the relevant systems of the automatic feeding mixer should be cleaned.

传动轴动平衡失效，摆动量大，引起主轴摆动油封偏磨。及时对传动轴进行校正或更换。

The dynamic balance failure of the transmission shaft and the large swing caused the eccentric wear of the main shaft swing oil seal. Correct or replace the transmission shaft in time.

系统回油不畅，回油管或散热器发生堵塞，造成泵马达壳腔压力加大，引起油封漏油。排除堵塞情况，并保证回油循环达到顺畅。

The oil return of the system is not smooth, and the oil return pipe or radiator is blocked, which increases the pressure of the pump motor housing cavity and causes oil leakage of the oil seal. Eliminate the blockage and ensure the smooth return oil circulation.

散热器不散热而造成油温过高，粘度、润滑性下降、油封过热密封失效。及时排除散热器故障，尽快为系统降温，避免泵马达出现磨损情况。必要时应让自动上料搅拌机熄火，用水冲洗泵马达、散热器壳体，以达到降温效果。

If the radiator does not dissipate heat, the oil temperature will be too high, the viscosity and lubricity will be reduced, the oil seal will overheat and the seal will fail. Remove the radiator fault in time, cool the system as soon as possible, and avoid the abrasion of the pump motor. If necessary, the automatic feeding mixer should be turned off, and the pump motor and radiator shell should be washed with water to achieve the cooling effect.