关于混凝土搅拌机上料装置的问题
来源：http://www.zkhntjbj.com/日期：2022-05-15
混凝土搅拌机会在使用期间不可避免的发生故障，比如说在搅拌时发现有碰撞声音，或者上料时有问题出现，下面我们主要来看看关于混凝土搅拌机上料装置的问题内容。
The concrete mixer will inevitably fail during use. For example, a collision sound is found during mixing, or there are problems during feeding. Let's take a look at the problem-solving contents of the feeding device of the concrete mixer.
混凝土搅拌时有碰撞声
There is collision sound during concrete mixing
原因：拌铲或刮板松脱或翘曲致使和搅拌筒碰撞。办法：紧固拌铲或刮板的连接螺栓，检修，调整拌铲，刮板和筒壁之间的间隙。
Cause: the mixing shovel or scraper is loose or warped, resulting in collision with the mixing drum. Solution: fasten the connecting bolts of the mixing shovel or scraper, repair and adjust the gap between the mixing shovel, scraper and the cylinder wall.
拌铲转动不灵运转声异常
The mixing shovel does not rotate properly, and the operation sound is abnormal
原因：搅拌装置缓冲弹簧失效。拌合料中有大颗粒物料卡住拌铲。加料过多，动力超载。
Cause: buffer spring of mixing device failed. The mixing shovel is stuck by large particles in the mixture. Excessive feeding and power overload.
办法：更换弹簧。卡赛的物料。按规定进料容量投料。
Solution: replace the spring. Clear the material card of the game. Feed according to the specified feeding capacity.
运转中卸料门漏浆
Slurry leakage of discharge door during operation
原因：卸料门封闭不严密。卸料门周围残存的粘接物过厚。
Cause: the discharge door is not tightly closed. The residual adhesive around the discharge door is too thick.
排出方法：调整卸料底板下方的螺栓，使卸料门封闭严密。残存的粘结物料。
Discharge method: adjust the bolts under the unloading base plate to make the unloading door tightly closed. Remove the remaining bonding materials.
上料斗运行不平稳
The operation of the upper hopper is not stable
原因：上料轨道翘曲不平，料斗滚轮接触不良。
Cause: the feeding track is warped and uneven, and the hopper roller is in poor contact.
排出方法：检查调整两条轨道，使轨道平直，轨面平行。、
Discharge method: check and adjust the two rails to make them straight and parallel
上料斗上升时越过上点而拉坏牵引机构
When the upper hopper rises, it crosses the upper solstice point and damages the traction mechanism
原因：自动限位失灵。自动限位挡板变形而不起作用。
Cause: automatic limit failure. The automatic limit baffle is deformed and does not work.
办法：检修或更换限位装置。调整限位挡板。
Solution: repair or replace the limit device. Adjust the limit baffle.
搅拌机轴端漏浆
Slurry leakage at shaft end of mixer
混凝土搅拌机轴端漏浆是因为在长时间的工作中，搅拌机浮动密封损坏导致。混凝土搅拌机轴端是受力集中的部位。混凝土搅拌机在工作中，轴端受力，因此，零部件的磨损也就相应要大。
The slurry leakage at the shaft end of the concrete mixer is caused by the damage of the floating seal of the mixer during long-time operation. The shaft end of concrete mixer is the part with concentrated stress. During the operation of concrete mixer, the stress on the shaft end is the largest, so the wear of parts is correspondingly large.
It is also important to maintain the concrete mixer in time and replace the seals in time. For more information, please visit our website at www.zkhntjbj.com Com consultation to understand!
全国服务热线
点击拨打服务热线：400-879-1999
