关于自动上料搅拌机年检的流程事项
来源:http://www.zkhntjbj.com/日期:2022-06-15
检查前,自动上料搅拌机需准备好驾照、驾驶证、保险单、年检所需费用。搅拌机到达现场后需填写年检申请表,年检申请表应由运输部门盖章,加盖单位公章或私自签名,并附身份证复印件。如果有违规记录,我们必须处理。不要根据自己的喜好改装车身外观(不能随意更换汽车外壳或发动机,也不能购买来历不明的汽车)。否则,它将无法通过外观。
Before the inspection, the driver's license, driver's license, insurance policy and annual inspection fees shall be prepared for the automatic feeding mixer. After the mixer arrives at the site, it is required to fill in the annual inspection application form, which shall be sealed by the transportation department, stamped with the official seal of the unit or signed privately, and attached with a copy of the ID card. If there is a violation record, we must deal with it. Don't modify the appearance of the car body according to your own preferences (you can't replace the car shell or engine at will, and you can't buy a car of unknown origin). Otherwise, it will not pass through the appearance.
下一步是检查。前后轴负载、脚刹、手刹、悬架、侧滑等都能用准确的数据显示您的混音器是否合格,还有灯光、大灯亮度等角度等,如果某一项不合格,可以在规定时间内复查。当然,复查需要分开支付。
The next step is safety inspection. Front and rear axle load, foot brake, hand brake, suspension, side slip, etc. can use accurate data to show whether your mixer is qualified, as well as the angle of light, headlight brightness, etc. if one item is unqualified, it can be rechecked within the specified time. Of course, the review needs to be paid separately.
此外使用后要记得保养,清理搅拌机内外,料门上的积料,并冲洗干净;放尽空压机贮气筒内的气体和积水;各润滑点加注润滑点,尤其是轴端密封处,切不可遗漏;冬季应放净水路内的液体;停机后所有开关处于非工作状态,并切断电源。
In addition, remember to maintain the mixer after use, clean the accumulated materials inside and outside the mixer and on the material door, and wash them thoroughly; Drain the gas and water in the air compressor air reservoir; The lubricating points shall be filled at each lubricating point, especially at the shaft end seal, and shall not be omitted; Discharge the liquid in the waterway in winter; After shutdown, all switches are in non working state and the power supply is cut off.
3月内检查保养:检查皮带的张紧情况,并作适当的调整;检查叶片,衬板的磨损情况;检查上、下机架,料仓,大斜皮带机等部件的连接螺栓是否牢固,地基是否下沉;检查螺栓输送机内是否有结块和杂物,如有则。
Inspection and maintenance within 3 months: check the belt tension and make appropriate adjustment; Check the wear of blades and lining plates; Check whether the connecting bolts of the upper and lower frames, silos, large inclined belt conveyor and other components are firm and whether the foundation sinks; Check whether there are lumps and sundries in the bolt conveyor, and remove them if any.
4周内检查保养:检查
自动上料搅拌机搅拌罐内残留砼的凝结情况,如有凝结应停机进行铲除(注意应切断电源专人看护),检查搅拌叶片与衬板间隙,如不适合进行调整;检查各电器元件是否有损坏现象,必要时修理或更换,检查各接线是否松动;检查减速箱内的润滑油的质量和液面高度,必要时加注或更换;检查供水系统中吸水底阀是否可靠;检查气路系统是否漏气,气缸动作是否可靠;拧开放淤塞,检查轴端密封情况,无异常后在拧入放淤塞。
Inspection and maintenance within 4 weeks: check the condensation of the residual concrete in the mixing tank of the automatic feeding mixer. If there is any condensation, shut down the machine for eradication (note that the power supply should be cut off and watched by a specially assigned person), check the gap between the mixing blade and the lining plate, and adjust it if it is not suitable; Check whether the electrical components are damaged, repair or replace them if necessary, and check whether the wiring is loose; Check the quality and liquid level of lubricating oil in the reduction gearbox, and fill or replace it if necessary; Check whether the suction bottom valve in the water supply system is reliable; Check whether the air circuit system leaks and whether the cylinder operates reliably; Screw in and remove the blockage, check the sealing condition of the shaft end, and screw in and remove the blockage after there is no abnormality.
5年检和大修:设备运行运行一年,除了对1、2、3、4项进行检查外,还应对自动上料搅拌机其他部件进行检查,进行检查维修和更换。
5 annual inspection and overhaul: after the equipment has been operated for one year, in addition to the inspection of items 1, 2, 3 and 4, other parts of the automatic feeding mixer shall also be inspected for comprehensive inspection, maintenance and replacement.
I hope the above can help you. For more relevant information, you can follow our website http://www.zkhntjbj.com , contact the professional customer service personnel to explain more and more detailed contents or questions for you, so that you can get some information here!