搅拌机进入工地施工行驶“慢”字为先
来源:http://www.zkhntjbj.com/日期:2022-05-25
自动上料搅拌机行驶过程中,“慢”字是一个。转弯时一定要慢。搅拌车高,容易翻车!进弯前要减速降档,过弯时尽量不要猛踩刹车。随时通过后视镜,注意观察罐子是否在转动,尽量调慢速度。因为速度太高,搅拌车容易摆动。满载时,走到大倾角路段时,先停罐。搅拌车高,停止罐体转动有利于保证车辆的稳定性。
"Slow" is a key word in the driving process of automatic feeding mixer. Be sure to turn slowly. The mixer truck has a high center of gravity and is easy to overturn! Slow down and downshift before entering the corner, and try not to slam on the brake when crossing the corner. Through the rearview mirror at any time, pay attention to observe whether the can is rotating and slow down as much as possible. Because the speed is too high, the mixer truck is easy to swing. When fully loaded, stop the tank first when walking to the section with large inclination angle. The center of gravity of the mixer truck is high, and stopping the rotation of the tank is conducive to ensuring the stability of the vehicle.
在糟糕的道路上,使用合适的低档超车。遇到不平路面、坑洼等情况,使用合适的低速档位通过,保证车子随时有爆发力。应尽可能避免使用木板和锋利的石头!
On bad roads, use the right low gear to overtake. In case of uneven roads, potholes and other situations, use the appropriate low-speed gear to ensure that the car has explosive power at any time. Boards and sharp stones should be avoided as far as possible!
上坡时建议是提前降档。如果搅拌车满了,要注意轻缓起步,上坡时要多加注意。你不应该随意降档,所以你可以提前降档。下坡时不要将重型车辆滑入空档。习惯在长时间驾驶或下坡之前测试刹车。不要在重型车辆挂空档时滑下坡。下坡转弯时,提前减速,然后降档再减速。带档制动效果好。
When going uphill, it is recommended to downshift in advance. If the mixer truck is full, pay attention to starting gently and pay more attention when going uphill. You shouldn't downshift at will, so you can downshift in advance. Do not slide heavy vehicles into neutral when going downhill. Get used to testing the brakes before driving for a long time or going downhill. Do not slide downhill when heavy vehicles are in neutral. When turning downhill, slow down in advance, then downshift and then slow down. Good braking effect with gear.
注意高度限制。施工现场路况复杂,注意树木等,尤其要防止划伤电线。此外,搅拌车进入工地时要多加注意一些事项,比如说:
Pay attention to the height limit. Pay special attention to the complex construction conditions, such as trees, wires, etc. In addition, pay more attention to some matters when the mixer truck enters the construction site, such as:
进入工地时,尽量走在中间。工地道路简单,路基松软。现在水泥搅拌车已经达到10多。如果他们靠近路边行驶,道路很容易被碾压塌陷,导致车辆翻车。
When entering the construction site, try to walk in the middle. The site road is simple and the subgrade is soft. Now the cement mixer has reached more than 10 square meters. If they drive close to the roadside, the road is easy to be crushed and collapsed, resulting in vehicle rollover.
提前下车检查倒车线。许多搅拌车在夜间工作。到达工地后,下车拿电筒查看倒车路线。如有障碍物、坑洼或比较松软的地方,记得及时清理钢钉等。
Get off in advance and check the reversing line. Many mixers work at night. After arriving at the construction site, you'd better get off the bus and take a flashlight to check the reversing route. If there are obstacles, potholes or soft places, remember to clean the steel nails in time.
![自动上料搅拌机](http://www.zkhntjbj.com/uploadfile/2022/0525/20220525052814733.jpg)
倒车时要慢。不要总是把头伸出车窗外,要照顾好两边的后视镜。如果您真的不确定,请在倒酒前停下来看清楚。很多路面刚被挖掘机铺的比较软,搅拌车容易陷进去。一档起步,缓慢均匀行驶,尽量把路线倒车直。如果要反复撞车,千万不要把方向盘撞死或者用力过猛。
Slow down when reversing. Don't always stick your head out of the window. Take good care of the rear-view mirrors on both sides. If you're really not sure, please stop and have a look before pouring the wine. Many roads just paved by excavators are relatively soft, and the mixer truck is easy to sink in. Start in first gear, drive slowly and evenly, and reverse the route as straight as possible. If you want to crash repeatedly, don't kill the steering wheel or use too much force.
另外,千万不要让
自动上料搅拌机在路上抛锚,否则有闷罐会很麻烦。点火前,检查发动机机油、防冻剂、润滑油和冷却水等。如果发现任何不足,请再次添加它们。启动后,让震击器低速旋转,检查周围的轮胎压力,看是否有漏气的轮胎。
In addition, do not let the automatic feeding mixer break down on the road, otherwise it will be very troublesome to have a stuffy tank. Before ignition, check engine oil, antifreeze, lubricating oil and cooling water. If you find any deficiencies, add them again. After starting, let the jar rotate at a low speed and check the surrounding tire pressure to see if there is a leaking tire.
然后用螺丝刀把轮胎缝里的石头挖出来,检查轮胎里是否有钉子。再次检查车灯,尤其是腰灯,并确保能照到轮胎的边缘,施工现场会经常堆放钢筋等,侧壁是很薄弱的,易损。用抹布清洁后视镜和车窗玻璃的两侧。施工现场路况复杂,光线不好,需要保证视线!
Then use a screwdriver to dig out the stone in the tire seam and check whether there are nails in the tire. Check the lamp again, especially the waist lamp, and ensure that it can shine on the edge of the tire. The construction site will often stack reinforcement, etc., and the side wall is very weak and vulnerable. Clean both sides of the rearview mirror and window glass with a rag. The road conditions on the construction site are complex and the light is not good. It is necessary to ensure the line of sight!
Therefore, before operating the mixer, you should check carefully and find the fault in time. Personnel safety is the top priority. Don't take chances. For more information, you can visit www.zkhntjbj.com Com follow consultation!