浅析如何处理上料搅拌机漏油现象！
来源：http://www.zkhntjbj.com/日期：2020-08-07
作为自动上料搅拌机主人，掌握一些小的维修技巧是很有必要的，今天我们讲一下搅拌机出现漏油现象怎么处理。
As the owner of the automatic feeding mixer, it is necessary to master some small maintenance skills. Today, we will talk about how to deal with the oil leakage of the mixer.
1、冬季起车时预热不足，油温过低，油液和油封没有达到工作温度。
1. In winter, the preheating is insufficient, the oil temperature is too low, and the oil and oil seal do not reach the working temperature.
处理方案：起车时，停罐怠速运转十到二十分钟，待油温正常后再转罐工作。
Solution: when starting, stop the tank and idle for 10 to 20 minutes, and then turn the tank to work after the oil temperature is normal.
2、使用时间长，油封正常磨损。
2. It has been used for a long time and the oil seal is worn normally.
处理方案：更换新油封。
Treatment plan: replace the oil seal with a new one.
3、液压油长期没有更换或滤芯质量不合格，液压油过脏，加速油封磨损。
3. The hydraulic oil has not been replaced for a long time or the quality of the filter element is unqualified, and the hydraulic oil is too dirty, which accelerates the wear of the oil seal.
处理方案：尽快更换液压油和滤芯。
Treatment plan: replace hydraulic oil and filter element as soon as possible.
4、液压油变质或乳化，润滑性能下降，加速油封磨损。
4. The deterioration or emulsification of hydraulic oil leads to the decline of lubricating performance and the acceleration of oil seal wear.
处理方案：尽快更换液压油和滤芯，严重时需要清洗系统。
Treatment plan: replace the hydraulic oil and filter element as soon as possible, and clean the system if it is serious.
5、传动轴动平衡失效，摆动量大，引起主轴摆动油封偏磨。
5. The dynamic balance of the transmission shaft fails and the swing momentum is large, which causes eccentric wear of the oil seal of the spindle swing.
处理方案：及时校正或更换传动轴。
Solution: correct or replace the transmission shaft in time.
6、泵支架松动、开焊或泵固定螺栓松动，引起液压泵整体抖动，油封磨损。
6. Pump bracket loose, open welding or pump fixed bolt loose, causing the overall vibration of the hydraulic pump, oil seal wear.
处理方案：经常检查，排除隐患，预防和避免故障。
Treatment plan: regular inspection, elimination of hidden dangers, prevention and avoidance of faults.
7、系统回油不畅，回油管或散热器堵塞，造成泵马达壳腔压力增大，引起油封漏油。
7. The oil return of the system is not smooth, the oil return pipe or radiator is blocked, resulting in the increase of the pressure in the pump motor housing cavity, resulting in oil seal leakage.
处理方案：排除堵塞，保持回油循环顺畅。
Treatment scheme: remove the blockage and keep the oil return circulation smooth.
8、散热器不散热，造成油温过高，粘度和润滑性下降、油封过热密封失效。
8. The radiator does not dissipate heat, causing the oil temperature to be too high, the viscosity and the lubricity to drop, the oil seal overheats and seals to fail.
处理方案：及时排除散热器故障，尽快为系统降温，防止泵马达磨损。必要时停自动上料搅拌机熄火，用水冲泵马达和散热器壳体降温。
Treatment plan: timely remove the radiator failure, cooling the system as soon as possible to prevent pump motor wear. If necessary, stop the automatic feeding mixer, and wash the pump motor and radiator shell with water to cool down.
The above is about how to deal with the problem of oil leakage in automatic feeding mixer. I hope it can help you. If you want to know more, please click on our automatic charging mixer http://www.zkhntjbj.com Official website.
全国服务热线
点击拨打服务热线：400-879-1999
