很多操作人员在工作期间会遇到过自动上料搅拌机不能行走的情况。如果不能正常行走，肯定会影响正常工作。但是，大家不要慌张，找原因，排除故障。下面就来简单分析一番吧。

Many operators will encounter the situation that the automatic feeding mixer cannot walk during work. If you can't walk normally, it will certainly affect your normal work. However, don't panic, find the reason and eliminate the fault. Let's make a simple analysis.

检查变速箱限油阀和变速箱压力表。如果发现变速箱和变距油缺失，应加新油，但不能过多，否则会引起变速箱发热。通常，将其添加到限制中油可以流出位置阀。

Check the transmission oil limit valve and the transmission pressure gauge. If the transmission and variable distance oil are found to be missing, add new oil, but not too much, otherwise the transmission will be heated. Usually, oil added to the limit valve can flow out of the position valve.

检查臂架能否升降，是否有转向。如果动臂可以升降，也可以完成转向动作，但机器本身无法实现行走的过程。这主要是由于变速泵损坏导致缺油缺水造成的。

Check whether the boom can rise and fall and whether there is steering. If the boom can rise and fall, it can also complete the steering action, but the machine itself cannot realize the walking process. This is mainly due to the lack of oil and water caused by the damage of variable speed pump.

臂架不能起降，不能实现转向动作，不能行走。这种情况多是由于搅拌斗传动的钢板连杆被螺栓剪断和弹力板断裂造成的。将柴油机和变速箱一起吊起，拆下变矩器柴油机的连接部位，检查损坏部位，更换修理零件。

The boom cannot take off and land, cannot realize steering action, and cannot walk. This situation is mostly caused by the steel plate connecting rod driven by the mixing bucket being cut off by bolts and the elastic plate being broken. Lift the diesel engine and gearbox together, remove the connecting parts of the torque converter diesel engine, check the damaged parts, and replace and repair parts.

另外，要防止燃油漏入油底壳，因为油底壳会稀释机油，使机油的粘度大大降低，过早失去润滑作用。良好的雾化和合理的节气门控制确保燃料的完全燃烧。

In addition, prevent the fuel from leaking into the oil pan, because the oil pan will dilute the oil, greatly reduce the viscosity of the oil and prematurely lose the lubricating effect. Good atomization and reasonable throttle control ensure the complete combustion of fuel.

避免发动机在高温环境下工作，发动机一般要求正常工作温度为80°C到95°C。如果温度过高，油会变稀，还会加速油的变质。一旦发现温度过高，要立即停机检查，排除故障后才能继续工作。

Avoid the engine working in high temperature environment. The normal working temperature of the engine is generally 80 ° C to 95 ° C. If the temperature is too high, the oil will become thin and accelerate the deterioration of the oil. Once the temperature is found to be too high, stop the machine immediately for inspection and continue to work after troubleshooting.

由于自动上料搅拌机长期使用会造成机械滤芯的堵塞，严重的堵塞会迫使阀打开，未经过滤的油液会在阀后直接进入动副表面被打开，这将加重机器。零件的磨损也会造成油底壳内杂质的堆积，加速油品的失效。因此，定期清洗过滤器和更换滤芯非常重要。

As the long-term use of the automatic feeding mixer will cause the blockage of the mechanical filter element, serious blockage will force the safety valve to open, and the unfiltered oil will directly enter the moving pair surface after the safety valve and be opened, which will aggravate the machine. The wear of parts will also cause the accumulation of impurities in the oil pan and accelerate the failure of oil products. Therefore, it is very important to clean the filter and replace the filter element regularly.

所以说，无论任何设备出现故障，都必须认真对待，找到问题的根源，然后找到相应的方案。更多内容就来网站www.zkhntjbj.com进行咨询吧。

Therefore, no matter any equipment fails, we must take it seriously, find the root cause of the problem, and then find the corresponding solution. For more information, please visit www.zkhntjbj.com Com.